| Customization: | Available |
|---|---|
| Standard: | Homeplug AV2 |
| OEM: | Accepted |
Suppliers with verified business licenses
Audited Supplier Audited by an independent third-party inspection agency
WD-B1201M-DIN industrial powerline Ethernet bridge is an industrial power line communication product developed by Kunshan WonderTek Technology Co., Ltd. This product is suitable for AC3*380V, AC220V power lines, and supports HomePlugA V2, Profinet, EtherNet/IP Modbus TCP communication protocol standards. It has been widely used in railways, mining, industrial communications, airports, subways, coal mines, intelligent warehousing, industrial automation control, automatic garages and many other wired or busbar sites.
2. Product characteristics
2.1 Technical parameters:
Support HomePlugAV2/HomePlugAV,Profinet,EtherNet/IP Modbus TCP Communication protocol protocol standard.
Industrial DIN rail installation, maximum transmission distance 600m.
Rate adaptation.
Compatible with all HomePlug/HomePlugAV2 devices.
2.2 Administrative:
Remote Firmware Upgrade (TR069).
802.3D Ethernet Bridge.
802.1Q VLAN.
Quality of Service(QoS).
IGMO(IPv4)Snooping&MLD(IPv6)Snooping.
2.3 Working environment:
Operating environment temperature:-40ºC-95ºC.
Operating environment working temperature:10%-90%
Storage humidity without condensation:5%-90% Non-condensing state.
2.4 Design standards:
IEC 60529
IEC 50022
IEC 60068-2-6 MIL-STD-810G
HomePlugAV
HomePlugAV2
3. Characteristics:
Packet loss rate: less than 0.01% (measured at 100M, load 70%).
Support 7*24 hours all-weather work.
With hardware watchdog function.
The PING value is less than 2MS.
4. Electrostatic Discharge Immunity:
The monitoring unit should be able to withstand the test voltage: ±6KV direct discharge, ±8KV air discharge.
The number of discharges for each sensitive test point: 10 times for positive and negative polarity, 1s interval between each discharge,
according to the requirements of B/T17626.2-2006.
5. Electrical fast transient pulse group (common mode) immunity:
The monitoring unit should be able to withstand the test voltage: between the power supply voltage break and the ground, ±2KV.
Between signal loop and ground:±1.0KV.
Repetition frequency:5KHz.
Test time:1min/times.
Test voltage times: 5 times for positive and negative polarity respectively.
It shall be carried out in accordance with the requirements of GB/T 17626.4-2008.
6. Anti-vibration:
Meet the MX3 level requirements of TB1433 (0~200HZ, 2g acceleration, maximum amplitude 7mm),
During the test, there is no loose interface, component desoldering or falling.
7. Product information parameters:
| Model | WD-B1201M-DIN |
| Interface | 1*100/1000M Ethernet port 1*capacitor coupler interface 1*DC10-80V power interface |
| LED Light | Ethernet signal light, PLC signal light, power light |
| Transmission Frequency | 2-68MHz |
| Protocol Standard (PHY) | IEEE802.3,IEEE802.3x,IEEE802.3u,HomePlugAV |
| Security protocol | 128-AES Data encryption and key management technology |
| Transfer Rate | 1200Mbps |
| Modulation | OFDM |
Manage |
802.1D Ethernet Bridge 802.1Q VLAN Quality of Service(QoS) |
| Working Environment | -20ºC~95ºC |
| Working voltage | DC10V~80V |
| Size | 120*90*45mm(L×W×H) |
| Weight | About 0.30kg |
| Operating environment | Working temperature: 10%-85% non-condensing Storage humidity 5%-90% non-condensing |
| Certification | FCC,CE class B,WEEE,RoHS |
8.Topology:
){kind=link}